Drilling Out the Restricted Fitting on the Back of the Cylinder Head

Download Article

Download Article

Lock cylinders are the internal mechanism within a lock. Interchangeable lock cylinders are often found in residential and office doors, while storefront lock cylinders are typically found in the doors for retail outlets and businesses. Lock cylinders can also be found in the ignition in most vehicles. If you want to change the key in your lock, it's likely you'll have to replace the lock cylinder. Luckily, doing so can be easy as long as you have the right tools and follow the right steps.

1. 1

   Remove the flat screw under the latch. Prop open the door as you change the lock. Turn the screw under the door latch counterclockwise with a flathead screwdriver and remove it.^[1]

   • Put the screw somewhere safe because you'll have to screw it back in later.

2. 2

   Turn the key a quarter of the way. Insert the key into the keyhole and turn it slightly so that it's in the open position. This will hide the latch in the internal components of the lock and allow you to slide it out.^[2]

   • If you don't turn the key then you won't be able to pull out the lock.

   Advertisement

3. 3

   Pull on the key while pushing on the other side of the lock. Keep the key turned while you push on the lock from the other side of the door. If done correctly, the interchangeable lock cylinder should come out.^[3]

   • If the cylinder feels stuck, try turning the key a little more or less. Adjust the key until you can push the latch out.

4. 4

   Turn the key and slide the new cylinder into the hole. Turn the key counterclockwise a quarter of the way open so that the latch goes inside of the lock cylinder. This will allow you to easily slide it back into the cylinder hole.^[4]

5. 5

   Screw the flat screw back in. Thread the screw into the hole with your fingers, then use a flathead screwdriver to tighten it. Continue turning it until it runs flush with the side of your door.^[5]

   • Screwing in the flat screw will hold the lock cylinder in place.

6. 6

   Test your key to make sure that it unlocks your door. Keep the door open as you test it. If it doesn't work, try dissembling and reinstalling the lock cylinder or call a locksmith to see if they can replace it for you.^[6]

   Advertisement

1. 1

   Unscrew and remove the faceplate over the latch. Use a doorstop to prop the door open while you're working. Find the faceplate on the thin part of the door and use a Phillips head screwdriver to remove all the screws in it. Once the screws are out, pop the faceplate off the door.^[7]

   • Place the screws in a sealable bag so that you don't lose them.

2. 2

   Loosen the set screw near the lock itself. The set screw will be the screw closest to the lock cylinder on the outside of the door. Use a Phillips head screwdriver to turn the set screw counterclockwise until you loosen it.^[8]

   • Loosening the set screw will allow you to rotate the lock cylinder. You don't have to remove the set screw entirely, just loosen it enough so that you can turn the lock cylinder.

3. 3

   Insert a key into the lock and turn it clockwise to unscrew it. Use a different key than the one that unlocks the door so that you can use it as a wrench. Insert the mismatching key into the keyhole and turn it counterclockwise to loosen the cylinder. When the cylinder is loose enough, it should easily come out of the hole in the door.^[9]

   • If you notice a lot of resistance, loosen the set screw more.

4. 4

   Thread a new lock cylinder into the hole. Put the new lock cylinder into the hole with the keyhole facing outward. Start threading the new cylinder by turning it clockwise in the hole.^[10]

   • If there is a lot of resistance as you're turning the key, it's an indication that the threads aren't catching correctly. In this case, unscrew the cylinder and start over from the beginning.

5. 5

   Insert a mismatching key into the lock and turn it clockwise. Again, use a key that isn't made for the lock so that it catches and can be used as a wrench. Stop turning the cylinder when you feel resistance and the keyhole is on the bottom of the lock.^[11]

   • As you turn the key, make sure that the threads on the cylinder are fitting in the threads around the hole for the lock.

6. 6

   Re-tighten the set screw. Turn the set screw clockwise to set the new lock cylinder in place. Once the set screw is tight, you should no longer be able to rotate the lock cylinder.^[12]

7. 7

   Screw the faceplate back on and test the lock. Fit the faceplate over the latch and line up the holes in the latch with the holes in the door. Use a screwdriver to secure the screws back in their holes. Use the correct key on the new lock to make sure that you installed it correctly and the door locks.^[13]

   Advertisement

1. 1

   Find the access hole to your ignition. Most models of cars will have an ignition access hole somewhere around the steering wheel. Check your user's manual to find it on your car. On Fords, there are usually 3 holes under your steering wheel. The smallest hole should be in the middle and is the access hole for your ignition.^[14]

   • On Chevrolet brand cars, the access hole can usually be found on the top of the steering wheel.^[15]
   • New cars that have electronic or push ignitions don't have lock cylinders.
   • If you don't have an ignition access hole, you'll need to remove the bottom of your steering wheel.

2. 2

   Put your key in the ignition. Your key needs to be in the ignition or you won't be able to release the lock cylinder. Keep the key in the ignition as you continue working. Do not turn on the car.^[16]

   • You don't have to turn the key initially.

3. 3

   Push an Allen key into the hole. As you push the Allen key into the hole, it should disengage the locking mechanism on the lock cylinder. You'll have to keep the Allen key pressed into the hole as you move onto the next step.^[17]

   • The Allen key disengages the locking mechanism in the lock cylinder.

4. 4

   Turn the ignition clockwise until it clicks. You should hear 2 clicks once the ignition disengages. Your car should not start. You can now release the Allen key from the hole.^[18]

   • Keep the key in the ignition.

5. 5

   Pull the key ignition out. The ignition, or lock cylinder, should pop out after you turn it. Pull on the key to pull the lock cylinder completely out of its casing. If the ignition is sticking, wiggle it back and forth until you free it from its hole.^[19]

6. 6

   Insert the new lock cylinder and turn it counterclockwise until it clicks. Push your new lock cylinder into the hole and twist it towards you. The spring should engage, locking the new cylinder into place. Your new lock cylinder is now installed.

   • You should hear it click when your ignition locks in place.

   Advertisement

Add New Question

• Question

  Is it cheaper to rekey or replace locks?

  

  This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Answer

  

  Support wikiHow by unlocking this staff-researched answer.

  Key pins are quite inexpensive, so it's usually cheaper to rekey your locks than to change them. Most locksmiths will only charge labor instead of charging you for both labor and parts, as they'd need to if you had your locks changed.

• Question

  How do you change the cylinder on a UPVC door lock?

  

  This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Answer

  

  Support wikiHow by unlocking this staff-researched answer.

  Unscrew the screw on the faceplate along the edge of the door. Put the key on the inside lock barrel and turn it slightly to the left and right wile pulling it toward you at the same time. Eventually, the cylinder will slide out. Simply reverse the process to install a new cylinder.

• Question

  What do you do if the lock cylinder pops out by accident?

  

  This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

  

  wikiHow Staff Editor

  Staff Answer

  

  Support wikiHow by unlocking this staff-researched answer.

  It this happens, it probably means that the lock has been damaged. For some kinds of locks, you can purchase a small retainer clip to help keep the cylinder in place. If the lock is too badly damaged, you may have to replace the whole thing.

• Question

  What do I do if I don't have the original key?

  

  You will need to extract the core from the lock and have a locksmith who knows how to work with Interchangeable Cores "decode" your core (take all the pins out of the core) and provide you with the key codes. You will then need to use the key code for the original key for the locksmith to create a copy of the key based on the original key code.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

• Flathead screwdriver
• Key

• Screwdriver
• Key

• Allen key
• Key

About This Article

Article Summary X

Replacing a lock cylinder can be done by following a few simple steps. First, you'll need to remove the screw below the latch. Then, turn your key a quarter of the way so it's in the open position, which will allow you to pull out the cylinder. You'll need to pull on the key while pushing the lock from the other side of the door, which should cause the cylinder to pop out. If it doesn't, try turning the key slightly more or less until the cylinder comes loose. When you're ready to install the new cylinder, turn the key a quarter of the way counter-clockwise so you can insert it. Then, insert the flat screw below the latch. For tips on how to replace a storefront lock cylinder, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 303,018 times.

Did this article help you?

Drilling Out the Restricted Fitting on the Back of the Cylinder Head

Source: https://www.wikihow.com/Change-a-Lock-Cylinder

Share this post